SV Technologies

This is a Plasma/Flame Intergrate CNC Cutting Controller Based on Arm9+FPGA high performance processor. This controller has a strong anti-interference capacity and can compatiable with most of Plasma power supply.

System Function:
TM200 Flame/Plasma CNC cutting machine controller is a high quality controller both for flame and plasma cutting.It is compatible with 99% servo / stepper kits ,Plasma cutter and THC

System Feature:

• High-reliable, Strong anti-EMI ability

• 32MB storage space, the cutting program can be 10000 lines
• English Language
• Multi- software functions, latest interpolation technology, very good performance for dealing with small lines, widely using in advertising ,Iron / steel industry
• Support dual-axis synchronization (X2, Y2 Axis)
• Dynamic 7 inch LCD display

• Adopt USB disk to Read/Write program and upgrade software.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Delivery Time: 10 days

Application:
XPTHC-100III supports almost all plasma cutters on market like Hypertherm, Thermal Dynamics…include HD plasmas like HPR130, 260, Ultra-cut series…. And it supports all CNC cutting controllers on market like Hypertherm, Burny industrial level controllers or Mach3 such DIY controllers, because XPTHC-100III can start Auto Height control with or without Auto enable signal from CNC. But with Auto enable/disable signal from CNC, THC would work better.

Basic Functions: 
A: Auto Initial Height Sensing(IHS)
Torch Retaining Cap IHS and Proximity Switch IHS (NPN and PNP), Proximity Switch IHS is backup for Torch Retaining Cap IHS for cutting dirty/rusty workpiece, needing the Anti-Collision Fixture(breakaway kit).

B: Torch Anti-Collision Function:
We designed Touch-Up circuit for Anti-Collision Function. No matter it is on Auto Control Model or Manual Control Model, when torch head touches the workpiece, THC would automatically lift torch up to IHS height. So with XPTHC-100, even in Manual Control Model, user doesn’t need to worry about torch head crashing.

C: Freeze Auto Height Control on Corner Signal:
XPTHC-100 can recognize Corner Signal from CNC and freeze Auto Control Model on receiving this signal, and we have a unique design to backup this function. We set 30V (adjustable) as Turning Point according to our years practice. When the Actual Arc Voltage is higher than Set Arc Voltage over 30V, THC Auto Control Mode freezes to avoid torch head diving, until it goes back to 30V range. This Over Voltage protection can avoid torch diving on voltage spikes (Corner Turning, Kerf Crossing) effectively.

D: Lifting torch Up on IHS Disabled status:
On IHS Disabled status, jogging torch head down until it reaches workpiece, when Arc Starts, torch head would lift up automatically to the Set Height set via the button SET-IHS.

E:Lifting Torch Up on TURN ON or Arc Off:
When CNC is TURN ON or Plasma Arc Off, THC would lift torch up for 2 seconds, please notice this Function during commissioning, avoiding the possible damage of limit switch or lift device.

F. Set Pierce Delay Time:
Set Button Set-PIERE (set Pierce delay time), to delay output this signal, it is a switch signal, set to detect arc voltage lead in THC. Once THC detect arc lead in, it send arc ok signal to CNC to start cut.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Chennai
• Delivery Time: 15 days

The system has high reliability design, with anti plasma interference, anti-lightning and surge capacity

It can be used in practical flame and plasma cutting process, plasma processing, automatic corner speed control
It can be used in wireless remote control or wired control box to achieve remote operation

With slotted compensation function, and testing procedures in compensation is reasonable, make corresponding reports for the user to choose.

It has breakpoint recovery, automatic power outage recovery function, automatic memory
It has arbitrary selections and selection of perforation point processing, processing can be arbitrary skip processing.

It has the function of the extension and perforation of thick plate, and the bridging function is suitable for the thick plate.
It has regression, excerpts, breakpoint recovery, optional position and other functions, greatly facilitate the user's control.
It can transfer cut at any time, choose the starting point processing, processing can be automatically broken.

It uses a small segment function, special walking smoothly, can be widely used in metal and advertising, iron etc..

It contains 24 kinds of graphics (expandable) parts library, including the commonly used basic processing parts.

Be fully compatible with the STARCAM set of software, as well as IBE (Germany), FASTCAM and other mainstream software package.

English and Chinese operation interface conversion, dynamic graphics display, Zoom the graphics 1 to 8 times, automatic tracking.

Using U disk to read the program and timely software upgrades.

Support LOGO image customization, users can modify their own logo (only for SF-2300S).

Upgrade button setting, easy to operate (only for SF-2300S).

Additional Information:

• Item Code: TM300
• Production Capacity: as per customer requirement
• Delivery Time: immediate
• Packaging Details: carton box packaging