SV Technologies

Control Axis

• Control axis 5 axis (X, Y, Z,4th,5th)
• Linkage axis 5 axis Feeding axis functions
• Position command range
• Metric input (G21)-9999.9999 mm-9999.9999mm, the mininum command unit 0.0001mm
• Inch input (G20)-999.9999inch-999.9999inch, the mininum command unit 0.0001inch
• Electronic gear ration command multiplier 1-65536, command multiplier1-65536
• Rapid traverse override F0, 25%, 50%, 100% four levels real-time tuning
• Cutting feedrate maximum feeding speed maximum 15m/min (G94) or 500.00mm/r (G95)
• Feedrate override 0-150% sixteen-level real-time tuning
• Manual feedrate 0-150 % sixteen-level real time tuning
• MPG feeding 0.001mm, 0.01mm, 0.1mm, 1mm four gears
• Single step feeding 0.001mm, 0.01mm, 0.1mm, 1mm four gears
• Interpolation mode linear interpolation, arc interpolation, spiral interpolation and ragid rapping
• Automatic chamfering function Acceleration/deceleration types
• Cutting feeding before the acceleration and deceleration linear type, before the acceleration and deceleration S type, after the acceleration and deceleration linear type and after the acceleration and deceleration index type.
• System with preview function, it can read 15 NC programming, make small line interpolation in high speed and smooth,
• Manual mode, handwheel mode is after acceleration and deceleration control, handwheel mode can choose emergency mode or full operation mode.
• Rapid positioning can choose linear or broken line.

Spindle Axis Functions

• Two channels 10V analog voltage output, support double spindle control
• Spindle encoder encoder lines can be set (100-5000 p/r)
• Encoder and spindle's transmission ratio (1-255)
• Spindle ration 50-120% eight stages real-time tunning in total
• Spindle axis constant line speed control
• Tapping circle, rigid tapping Precision compensation
• Thread pitch error compenstation Compensation points, compensation interval, compensate original position can be set.
• Backlash compensation can set reverse interval to interpolation machine tool by fixed frequency or lifting speed mode.

PLC Functions:

• Two levels PLC programming, operation speed is 1.5μs/ step basic instruction; 4700 steps mostly, the cycle of the first level programming is 8ms.
• Support PLC warning and PLC alarm.
• Support multiply PLC programming (mostly 20), the current PLC programming can be chosen.
• 45 kinds of commands (10 kinds of basic commands, 35 kinds of function commands)
• I/O unit input/output 36/36

Program Edit:

• Program volumn 56 MB, it can store 400 programmings mostly (includes sub-programming, Marco programming)

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Chennai
• Delivery Time: 15 Days

TAC-1003T milling controller is a new generation of cnc system developed by tomatech.Like the updated version, it supports the crushing, drilling and drilling cycle. It employs 32 bitsHigh capacity CPU and very large scale programmable fpga device, applies in real timeMulti-task control technology and hardware interpolation technology, and is capable of executingPrecim level precisionmotion control and plc logic control   Characteristics

* Three axis control; connection of 3 axes; 2 analog axes

* Ms interpolation cycle, 0.1mm control accuracy.

* Wo channels 0 v output 10 v analog voltage output, support double shaft control

* Linear type, type of index and type of s etc. types of acceleration and deceleration can be chosen.

* Incorporated with plc programming, the current schedule of the running plc can be chosen

* Plc displayed online, real-time monitoring, real-time tracking signal

* Supports the type of macro programming instruction, supports macro codes with parameter calls.

* Flexible beat and rigid beat can be adjusted by parameters

* Includes spiral, scale, polar coordinates, fixed circle AND a variety of notched composite cycle function.

* Includes historical alarm and summary operation functions, it is convenient for users to operate and maintain.

* Multi-level password support for equipment maintenance and management

* 32 general entry point / 32 general exit point

* RS232 standard support and USB port, support u disk operation documents, system configuration and software

Updated, you can find the functions that transfer documents, serial ports dnc machining and usb online machining

Display interface:

* 7.0 inch wide screen LCD, 800 × 480 network

* Chinese, English etc multiply the language display

* 2d toolpath displays.

* Real time clock

Operation mode:

* Operation modes: edit, automatic, input, machine tool restoration, steering wheel / single-step, manual, dnc.

* Management of multiple operational authority.

* Alarm log

Edition of the program:

* Volumn program: 56 mb, it can store mostly 400 programmings (includes sub-programming, milestone programming)

* Editing function: programming / programming segment / word retrieval, change, delete, copy and stick

* Programming format: iso code, supports macro instruction program, supports relative coordinates, absolute

Polar coordinates and coordinates.

* Programming calls: supports maco with parameter calls, level 4 subprogram nesting.

Communication function:

* Rs232: parts program, parameters and some bidirectional transmission of documentation, supports plc program, system

Updating software serial ports.

* Usb: u disk documentation operatiom, u disk processing directly, support plc program, u disk system software

Update.

* Support dnc serial port processing function and usb inline processing function, reliability and safty

Relability and safety function

* Emergency stop button

* Route limit gloves 

* Software routet inspect

* Data backups and data recovery.

TAC-1002T Series CNC 2 Axis Lathe Controller is a new generation CNC turning controller, It based Arm9+FPAG large scale CPU and processor ,Meet 2 Axes lathe machine. this controller support ISO G codes, Macro program and PLC ladder, very flexible for unstandard function design.

 

Control Axis

•  Interpolation axes X, Z linear interpolation; X and Z two axes linear and circular Interpolation, any two axes arc interpolation

Feeding Axis Function:

• Minimum command unit 0.001mm or 0.0001mm can be selected
• Position command range +/- 99999999 x minimum command unit
• Rapid traverse speed When the command unit is 0.001mm, the (0.0001mm, the maximum speed is 24m/min)
• Rapid override F0, 25%, 50% and 100%, total four levels, real-time adjustment;
• Feeding override total 16 levels 0-150%, real-time adjustment;
• Interpolation mode linear, arc and spiral interpolation and rigid tapping
• Cutting feeding Acceleration or deceleration in linear type/index type or front/rear is selectable.
•  Rapid traverse Acceleration or deceleration in linear type/index type or front/rear is selectable
•  Tapping Acceleration or deceleration in linear type/index type or front/rear is selectable.
•  The starting speed, finishing speed and time of acceleration and deceleration are set by the parameter.

Spindle Function:

• Analog voltage 0-10V output in two channels, support two-spindle control
• Spindle encoder feed back in one channel, the resolution of spindle encoder can be set (0 or 100-5000p/r)
• Transmission ratio between encoder and spindle is (1-255)
•  Spindle speed It is specified by S code or PLC signal, the speed range is 0-9999rpm.
• Spindle override total 8 levels 50-120%, real-time adjustment
•  Spindle constant surface speed control
• Tapping cycle/rigid tapping

Tool Function:

• Tool length compensation
• Tool radius compensation (C type)

 

PLC Function:

•  PLC program in two levels, maximum 5,000 steps, the refresh cycle of the 1st level program 8ms.
•  PLC program communication download
• Support PLC warning and PLC alarm
• Support many PLC programs (maximum 16), the current running PLC program can be selected
• Basic I/O input in 40 points/output in 32 points

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Chennai
• Delivery Time: 15 days

TAC-1003M Series 3 Axis CNC Milling Controller is a new generation of CNC system developed by TOMATECH.As the upgraded version, it supports milling, boring and drilling cycle. It employs 32 bits high-capability CPU and very large scale programmable device FPGA, applies real-time multi-task control technology and hardware interpolation technology, and is able to perform μm level precision motion control and PLC logic control.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Chennai
• Production Capacity: 15/month
• Delivery Time: Immediate

TAC-1004M Series CNC 4 Axis Milling Controller is a new generation of CNC system developed by Tomatech.As the upgraded version, it supports milling, boring and drilling cycle. It employs 32 bits high-capability CPU and very large scale programmable device FPGA, applies real-time multi-task control technology and hardware interpolation technology, and is able to perform μm level precisionmotion control and PLC logic control.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Chennai
• Delivery Time: 15 days

Control Axis:

1. Control axes 5 axes (X, Z, Y, 4th and 5th)

2. Interpolation axes X, Y, Z, 4th and 5th linear interpolation; X,Y and Z three axes linear and spiral

interpolation, any two axes arc interpolation;

3. PLC control axes 5 axes

Feeding Axis Function:

1. Minimum command unit 0.001mm or 0.0001mm can be selected

2. Position command range +-99999999 x minimum command unit

3. Rapid traverse speed When the command unit is 0.001mm, the maximum speed is 60m/min; (0.0001mm, the maximum speed is 24m/min)

4. Rapid override F0, 25%, 50% and 100%, total four levels, real-time adjustment;

5. Feeding override total 16 levels 0~150%, real-time adjustment;

6. Interpolation mode linear, arc and spiral interpolation and rigid tapping

7. Auto chamfering

Acceleration and Deceleration Function:

1. Cutting feeding Acceleration or deceleration in linear type/index type or front/rear is selectable.

2. Rapid traverse Acceleration or deceleration in linear type/index type or front/rear is selectable.

3. Tapping Acceleration or deceleration in linear type/index type or front/rear is selectable.

4. The starting speed, finishing speed and time of acceleration and deceleration are set by the parameter.

Spindle Function:

1. Analog voltage 0V~10V output in two channels, support two-spindle control

2. Spindle encoder feed back in one channel, the resolution of spindle encoder can be set (0 or 100p/r~5000p/r)

3. Transmission ratio between encoder and spindle is(1~255)(1~255)

4. Spindle speed It is specified by S code or PLC signal, the speed range is 0rpm~9999rpm.

5. Spindle override total 8 levels 50%~120%, real-time adjustment

6. Spindle constant surface speed control

7. Tapping cycle/rigid tapping

Tool Function

1. Tool length compensation

2. Tool radius compensation (C type)

3. Tool wearing compensation

4. Tool life management

 

 

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Chennai
• Delivery Time: 15 Days

A manual pulse generator (MPG) is a device normally associated with computer numerically controlled machinery or other devices involved in positioning. It usually consists of a rotating knob that generates electrical pulses that are sent to an equipment controller. The controller will then move the piece of equipment a predetermined distance for each pulse.
The CNC handheld controller MPG Pendant with x1, x10, x100 selectable. It is equipped with our popular machined MPG unit, 4 axis and scale selector, emergency stop and reset button

Additional Information:

• Item Code: TAC4A2
• Production Capacity: As per Requirement
• Delivery Time: Immediate
• Packaging Details: Carton Box Package